ROUTING STATIC METODE NEXT HOP 3 ROUTER CISCO


rumus command routing static:

contoh disini dari Router-0 mau nge-ping ke PC-1/192.168.20.2




ROUTER-0:
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router#hostname Router-0
Router-0(config)#interface ra gigabitEthernet 0/0-1
Router-0(config-if-range)#no sh

%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router-0(config)#interface gi0/0
Router-0(config-if)#ip add 10.10.10.2 255.0.0.0
Router-0(config-if)#ex
Router-0(config)#interface gi0/1
Router-0(config-if)#ip add 192.168.10.1 255.255.255.0
Router-0(config-if)#ex
Router-0(config)#ip route 192.168.20.0 255.255.255.0 10.10.10.2
Router-0(config)#ip route 192.168.30.0 255.255.255.0 10.10.10.2
Router-0(config)#ex

untuk melihat tab route static, lakukan command:
Router-0#show ip route static 
S    20.0.0.0/8 [1/0] via 10.10.10.1
S    192.168.20.0/24 [1/0] via 10.10.10.1
S    192.168.30.0/24 [1/0] via 10.10.10.1


ROUTER-1:
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname Router-1
Router-1(config)#interface ra gigabitEthernet 0/0-2
Router-1(config-if-range)#no sh

%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to up

Router-1(config)#interface gi0/0
Router-1(config-if)#ip add 10.10.10.1 255.0.0.0
Router-1(config-if)#ex
Router-1(config)#interface gi0/1
Router-1(config-if)#ip add 20.20.20.1 255.0.0.0
Router-1(config-if)#ex
Router-1(config)#interface gigabitEthernet 0/2
Router-1(config-if)#ip add 192.168.20.1 255.255.255.0
Router-1(config-if)#ex
Router-1(config)#ip route 192.168.10.0 255.255.255.0 10.10.10.2
Router-1(config)#ip route 192.168.30.0 255.255.255.0 20.20.20.2
Router-1(config)#ex

Router-1#show ip  route static 
S    192.168.10.0/24 [1/0] via 10.10.10.2
S    192.168.30.0/24 [1/0] via 20.20.20.2


ROUTER-2:
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router-2(config)#hostname Router-2
Router-2(config)#interface ra gigabitEthernet 0/0-1
Router-2(config-if-range)#no sh

%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router-2(config)#interface gi0/0
Router-2(config-if)#ip add 20.20.20.2 255.0.0.0
Router-2(config-if)#ex
Router-2(config)#interface gi0/1
Router-2(config-if)#ip add 192.168.30.1 255.255.255.0
Router-2(config-if)#ex
Router-2(config)#ip route 192.168.20.0 255.255.255.0 20.20.20.2
Router-2(config)#ip route 192.168.30.0 255.255.255.0 20.20.20.2
Router-2(config)#ex

Router-2#show ip route statitc
S    20.0.0.0/8 [1/0] via 20.20.20.1
S    192.168.10.0/24 [1/0] via 192.168.20.1
S    192.168.20.0/24 [1/0] via 20.20.20.1

Lakukan pemasangan ip secara static pada PC dengan rincian sebagai berikut:

PC-0: Ip address 192.168.10.2 netmask:255.255.255.0 gateway:192.168.10.1
PC-1: Ip address 192.168.20.2 netmask:255.255.255.0 gateway:192.168.20.1
PC-0: Ip address 192.168.20.2 netmask:255.255.255.0 gateway:192.168.20.1

Postingan populer dari blog ini

ROUTING STATIC Metode Floating

Gambar
 Pasang IP di PC-0 : 192.168.10.10/24                            PC-1  : 192.168.30.10/24 Pasang  HWIC-2T di masing-masing Router, pasang persis seperti ini: Router0: Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#int f0/0 R-0(config)# hostname R-0 R-0(config-if)#ip add 192.168.10.1 255.255.255.0 R-0(config-if)#no sh R-0(config-if)#int se0/0/0 R-0(config-if)#ip add 192.168.20.1 255.255.255.252 R-0(config-if)#no sh R-0(config-if)#int se0/0/1 R-0(config-if)#ip add 192.168.20.5 255.255.255.252 R-0(config-if)#no sh Router1: Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#hostname R-1 R-1(config)#int f0/0 R-1(config-if)#ip add 192.168.30.1 255.255.255.0 R-1(config-if)#no sh R-1(config-if)#int se0/0/0 R-1(config-if)#ip add 192.168.20.2 255.255.255.252 R-1(config-if)#no sh R-1(co...
Baca selengkapnya

KONFIGURASI VLAN + ROUTING STATIC DI H3C

Gambar
 Topologi: disini saya menggunakan Multi Layer Switch(MLS) H3C 29850 Series, saya akan menggunakan penyebutan MLS-1 untuk S9850-1,dan juga MLS-2/3 pada masing-masing perangkat. konfigurasi hostname dan point-to-point antar MLS pada masing-masing MLS MLS-1: <H3C>system-view System View: return to User View with Ctrl+Z. [H3C]hostname MLS-1 [MLS-1]interface HundredGigE 1/0/1 (interface ke arah MLS-2) [MLS-1-HundredGigE1/0/1]ip address 192.168.100.2 255.255.255.252 [MLS-1-HundredGigE1/0/1]no shutdown [MLS-1-HundredGigE1/0/1]quit MLS-2: <H3C>system-view System View: return to User View with Ctrl+Z. [H3C]hostname MLS-2 [MLS-2]interface HundredGigE 1/0/1  (interface ke arah MLS-1) [MLS-2-HundredGigE1/0/1]ip address 192.168.100.1 255.255.255.252 [MLS-2-HundredGigE1/0/1]no shutdown [MLS-2-HundredGigE1/0/1]quit [MLS-2]interface HundredGigE 1/0/2  (interface ke arah MLS-3) [MLS-2-HundredGigE1/0/2]ip address 192.168.200.1 255.255.255.252 [MLS-2-HundredGigE1/0/2]no shutdow...
Baca selengkapnya

Ujikom BPN 14-10-2022

Gambar
1. pasang ip pada masing masing end device terlebih dahulu 2. setting switch mode access, mode trunk,port-security dan ether-channel sesuai perintah di topologi SW-01: SW-01>en SW-01#conf t Enter configuration commands, one per line.  End with CNTL/Z. SW-01(config)#vlan 100 SW-01(config-vlan)#name Rumah-Emak SW-01(config-vlan)#int ra fa0/3-4 SW-01(config-if-range)#sw mode acc SW-01(config-if-range)#sw acc vlan 100 SW-01(config-if-range)#int gig 0/1 SW-01(config-if)#sw mode tru (setting port-security) SW-01(config-if)#int f0/4 SW-01(config-if)#sw port-security *lakukan ping dahulu dari DNS-SVR ke DHCP-SVR agar mac-addressnya tercatat oleh Switch SW-01(config-if)#sw port-security mac-address sticky SW-01(config-if)#switchport port-security maximum 1 SW-01(config-if)#switchport port-security violation shutdown  SW-02: SW-02>en SW-02#conf t Enter configuration commands, one per line.  End with CNTL/Z. SW-02(config)#vlan 200 SW-02(config-vlan)#name Wisma SW-02(config-vla...
Baca selengkapnya