ROUTING STATIC Metode Floating


 Pasang IP di PC-0 : 192.168.10.10/24

                      PC-1 : 192.168.30.10/24

Pasang HWIC-2T di masing-masing Router, pasang persis seperti ini:



Router0:
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
R-0(config)# hostname R-0
R-0(config-if)#ip add 192.168.10.1 255.255.255.0
R-0(config-if)#no sh
R-0(config-if)#int se0/0/0
R-0(config-if)#ip add 192.168.20.1 255.255.255.252
R-0(config-if)#no sh
R-0(config-if)#int se0/0/1
R-0(config-if)#ip add 192.168.20.5 255.255.255.252
R-0(config-if)#no sh

Router1:
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname R-1
R-1(config)#int f0/0
R-1(config-if)#ip add 192.168.30.1 255.255.255.0
R-1(config-if)#no sh
R-1(config-if)#int se0/0/0
R-1(config-if)#ip add 192.168.20.2 255.255.255.252
R-1(config-if)#no sh
R-1(config-if)#int se0/0/1
R-1(config-if)#ip add 192.168.20.6 255.255.255.252
R-1(config-if)#no sh


sekarang setting routing static-nya


Router0:

R-0(config-if)#ip route 192.168.30.0 255.255.255.0 192.168.20.2

R-0(config)#ip route 192.168.30.0 255.255.255.0 192.168.20.6 10


Router1:

R-1(config-if)#ip route 192.168.10.0 255.255.255.0 192.168.20.1

R-1(config)#ip route 192.168.10.0 255.255.255.0 192.168.20.5 10


Lakukan trace route dari pc-0 ke pc-1:


terlihat pc-0 melalui jalur 192.168.20.1(serial0/0/0) untuk bisa sampai ke pc-1


sekarang kita akan matikan port serial0/0/0 di R-0:

R-0(config)#int se0/0/0
R-0(config-if)#sh
R-0(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to administratively down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to down


kita lakukan lagi trace route dari pc-0 ke pc-1:


nah sekarang terlihat pc-0 berubah jalur ke 192.168.20.6(serial0/0/1) untuk bisa sampai ke pc-1, karena serial0/0/0 di shutdown/dimatikan


Postingan populer dari blog ini

KONFIGURASI VLAN + ROUTING STATIC DI H3C

Gambar
 Topologi: disini saya menggunakan Multi Layer Switch(MLS) H3C 29850 Series, saya akan menggunakan penyebutan MLS-1 untuk S9850-1,dan juga MLS-2/3 pada masing-masing perangkat. konfigurasi hostname dan point-to-point antar MLS pada masing-masing MLS MLS-1: <H3C>system-view System View: return to User View with Ctrl+Z. [H3C]hostname MLS-1 [MLS-1]interface HundredGigE 1/0/1 (interface ke arah MLS-2) [MLS-1-HundredGigE1/0/1]ip address 192.168.100.2 255.255.255.252 [MLS-1-HundredGigE1/0/1]no shutdown [MLS-1-HundredGigE1/0/1]quit MLS-2: <H3C>system-view System View: return to User View with Ctrl+Z. [H3C]hostname MLS-2 [MLS-2]interface HundredGigE 1/0/1  (interface ke arah MLS-1) [MLS-2-HundredGigE1/0/1]ip address 192.168.100.1 255.255.255.252 [MLS-2-HundredGigE1/0/1]no shutdown [MLS-2-HundredGigE1/0/1]quit [MLS-2]interface HundredGigE 1/0/2  (interface ke arah MLS-3) [MLS-2-HundredGigE1/0/2]ip address 192.168.200.1 255.255.255.252 [MLS-2-HundredGigE1/0/2]no shutdow...
Baca selengkapnya

Ujikom BPN 14-10-2022

Gambar
1. pasang ip pada masing masing end device terlebih dahulu 2. setting switch mode access, mode trunk,port-security dan ether-channel sesuai perintah di topologi SW-01: SW-01>en SW-01#conf t Enter configuration commands, one per line.  End with CNTL/Z. SW-01(config)#vlan 100 SW-01(config-vlan)#name Rumah-Emak SW-01(config-vlan)#int ra fa0/3-4 SW-01(config-if-range)#sw mode acc SW-01(config-if-range)#sw acc vlan 100 SW-01(config-if-range)#int gig 0/1 SW-01(config-if)#sw mode tru (setting port-security) SW-01(config-if)#int f0/4 SW-01(config-if)#sw port-security *lakukan ping dahulu dari DNS-SVR ke DHCP-SVR agar mac-addressnya tercatat oleh Switch SW-01(config-if)#sw port-security mac-address sticky SW-01(config-if)#switchport port-security maximum 1 SW-01(config-if)#switchport port-security violation shutdown  SW-02: SW-02>en SW-02#conf t Enter configuration commands, one per line.  End with CNTL/Z. SW-02(config)#vlan 200 SW-02(config-vlan)#name Wisma SW-02(config-vla...
Baca selengkapnya